mcgyvr

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 77 total)
  • Author
    Posts
  • in reply to: TinyG for Android #9987
    mcgyvr
    Member

    Matt,
    Sorry I can’t help..
    I gave up on tinyg and moved on to other software/hardware and haven’t looked back as it did everything I needed, just plain worked right out of the box and hasn’t skipped a beat in 2 years running a few hours a day..

    in reply to: struggling with v.6 board – firmware? #6126
    mcgyvr
    Member

    Run it with the spindle off/out of the way ( a few times)..
    If it makes it through.. then you have a noise problem caused by the spindle.

    If it doesn’t it could be noise from stepper motor cabling or other sources still..
    Do you have limit/homing switches wired? (disconnect them and try running the file)

    Are you stepper cables shielded?
    Are your limit switch cables shielded?
    I had bad noise issues with a V7 board and had to redo all wiring to shielded and add capacitors across the switch inputs for some additional filtering.

    http://www.cnccookbook.com/CCCNCNoise.html

    in reply to: struggling with v.6 board – firmware? #6103
    mcgyvr
    Member

    just type $ in the coolterm and hit enter
    or $$ to return all settings

    in reply to: Help connecting cooling fan… #6078
    mcgyvr
    Member

    see diagram/comments on right side about fan. (bet you just don’t have the jumper in place)
    Always a good idea to probe the pins with a multimeter to ensure you have the proper voltage.
    https://github.com/synthetos/TinyG/wiki/1.01-TinyG-Start
    You put the jumper across the middle pin and the 12V pin.

    in reply to: Electronics Shopping List Approval Needed #6039
    mcgyvr
    Member

    yeah hard to answer any of those questions with the details provided.

    but yes you will ABSOLUTELY need a fan to blow on the tinyg board with 4 x Nema23 @ 3A..(50+ cfm blowing directly on the bottom)

    in reply to: TinyG for Android #5951
    mcgyvr
    Member

    Matt,
    You still around? Does this app work on the newer versions of tinyg firmware..
    I tried it on 412.01 and it said connected but nothing really happens.. No status/no polling of tinyg configurations,etc..

    mcgyvr
    Member

    I’m confused…
    So is this a know issue in tinyg? or is this a machine specific mechanical issue (like missing steps due to mechanical issues/binding,etc..) or do they not know yet..

    I’ve seen this and sparkcrafters posts and can’t tell if the cause is known yet or if you guys are just over driving your machines and experiencing missed steps/backlash,etc..

    • This reply was modified 10 years, 7 months ago by mcgyvr.
    in reply to: Reset to Factory Defaults #5697
    mcgyvr
    Member

    not alden/riley but when FW is loaded “factory defaults” come alive..
    defa=1 is just a quick way to reset it all back to those defaults when you want to just say screw it and start fresh..
    I’d suspect cswiger just had some setting incorrect.. As he has reset them we will never know what the problem is..

    After I adjust configs I’ll do a $$ and then copy all the settings to a text file to reference back to later..

    in reply to: Mechanical Specs for v8 #5624
    mcgyvr
    Member
    in reply to: edge build to master #5623
    mcgyvr
    Member

    Sounds good..thanks Alden..

    in reply to: edge build to master #5621
    mcgyvr
    Member

    So can I just download/run the edge version..Or ..I guess..have you done all necessary bug fixes,etc.. that you were intending to do to it?

    Or what is your recommendation for me. I just want to load whatever version of the firmware/tgfx and be up and running as headache free as possible now.

    in reply to: edge build to master #5618
    mcgyvr
    Member

    Guess not…

    in reply to: 1st Motor Driver Appears Failed #5605
    mcgyvr
    Member

    Its just customerservice@synthetos.com
    no “s” at the end of service..

    in reply to: Small Arc errors – TinyG/tgFX – Engraving job #5589
    mcgyvr
    Member

    cmcgrath,
    Here is your code backplotted in my HSM Express editor..
    Quick glance looks perfect to me..
    https://dl.dropboxusercontent.com/u/9726802/TinyG/cmcgrathbackplot.PNG

    in reply to: TinyG/CoolTerm crashing solved #5563
    mcgyvr
    Member

    ^^ make sure you right click on that tingy.hex file and download/save it and not just let it open in the browser..

Viewing 15 posts - 1 through 15 (of 77 total)