mristau

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 33 total)
1 2 3
  • Author
    Posts
  • June 4, 2024 at 4:02 pm in reply to: TinyG stops responding after (failed?) Home Z #12182
    mristau
    Member

    What app are you using to send commands?
    Are you using the same computer as you were previous use?

    June 4, 2024 at 1:41 pm in reply to: TinyG stops responding after (failed?) Home Z #12179
    mristau
    Member

    What app are you using to send commands?

    I posted a question a week or so ago and got a response in a day or two. Patience I suppose.

    Have you tried contacting directly instead of posting to forum?

    • This reply was modified 10 months, 1 week ago by mristau.
    January 24, 2022 at 12:55 pm in reply to: Homing prob with Y axis #12126
    mristau
    Member

    Yep: Some power management settings got scrambled. Not sure how!

    December 19, 2019 at 10:52 am in reply to: plotting speed #11732
    mristau
    Member

    What software do you use to generate Goode files?

    December 6, 2019 at 7:38 pm in reply to: Strange CoolTerm Connection Issues #11712
    mristau
    Member

    cnc at melristau.com

    December 6, 2019 at 7:22 pm in reply to: Strange CoolTerm Connection Issues #11709
    mristau
    Member

    unsure why link is not posting. contact me directly?

    • This reply was modified 5 years, 4 months ago by mristau.
    December 6, 2019 at 7:19 pm in reply to: Strange CoolTerm Connection Issues #11707
    mristau
    Member

    I believe you can launch Coolterm from the “SlowSend.stc” file included in link to folder. Images of my Options settings as well.
    I always send “$$” as first line command to make sure TinyG is talking.
    Hope this helps

    • This reply was modified 5 years, 4 months ago by mristau.
    November 30, 2019 at 1:27 pm in reply to: Footer Code #11698
    mristau
    Member

    This seem to accomplish what I need:

    begin FOOTER

    “G1Z1”
    “G1x0y0”
    “G1z0”

    With this I can run sequence of project files without re-homing and re-positioning for G92. (Hopefully avoiding any position differences resulting from re-homing for each project file.)

    • This reply was modified 5 years, 4 months ago by mristau.
    March 9, 2018 at 12:18 am in reply to: Z Axis inconstancy in depth #10902
    mristau
    Member

    “I am new to CNC machining.”
    This isn’t your CNC’s first job?
    You’ve run other jobs cutting similar sized material with no problem?
    What kind of spindle are you using?
    Spoil board has been leveled?

    March 8, 2018 at 12:55 pm in reply to: Z Axis inconstancy in depth #10899
    mristau
    Member

    Might your chucked bit need tightening? And is your bit sharp?

    Cutting MDF or Partical Board with dull bit can pull the bit out of the chuck. Z-axis not perfectly perpendicular to cutting compounds this problem.

    November 4, 2016 at 8:39 pm in reply to: Dual Stepper Y axis misbehaving #10016
    mristau
    Member

    Drop boxed my dual y for you:

    https://www.dropbox.com/s/9vlmynyht8dv7dn/%24%24%20Dual%20Y%20setup.txt?dl=0

    March 11, 2016 at 12:51 pm in reply to: TinyG for 60W CO2 laser #9426
    mristau
    Member

    I have strong interest in using a spare tingG to build a low wattage lasercutter. Might either of you point me to TinyG setup parameters for (I suppose: 2 axis movement + laser control)?

    December 24, 2015 at 12:50 am in reply to: Ghost Limit Switch Error #9194
    mristau
    Member

    Thanks!
    I disabled all switches and ran the job. Set xyz minimums to home only and will test that in the morning.
    By the way, I replaced the switch wiring with shielded cables and that did correct the problem.

    December 23, 2015 at 5:42 pm in reply to: Ghost Limit Switch Error #9185
    mristau
    Member

    Problem is back!
    Cutting position is no where near limit switches. Deadline for parts I’m cutting looming. Help!
    Best I can do is replace a switch. If I only knew which one. Does the “240” in error message indicate anything in this regard?

    {“sr”:{“posx”:9.276}}
    {“sr”:{“posx”:9.337}}
    {“er”:{“fb”:440.18,”st”:204,”msg”:”Limit switch hit – Shutdown occurred”}}

    {“sr”:{“posx”:10.230}}
    {“sr”:{“posx”:10.167}}
    {“er”:{“fb”:440.18,”st”:204,”msg”:”Limit switch hit – Shutdown occurred”}}

    December 14, 2015 at 10:48 pm in reply to: Ghost Limit Switch Error #9145
    mristau
    Member

    Thanks – I thought noise might be the culprit too. Moved some wires around and it hasn’t occurred again. Dry here most of the time. Those two one hour jobs were acrylic. Maybe static related to material? My first time cutting acrylic on this machine.

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 33 total)
1 2 3