Riley

Forum Replies Created

Viewing 15 posts - 241 through 255 (of 260 total)
  • Author
    Posts
  • in reply to: Extra Steps? #1474
    Riley
    Keymaster

    Chris,

    Also, when you say missing steps. Is that on G0? or G1’s etc.. If you are doing G0’s and missing steps try setting your:

    $XSR
    $YSR
    $ZSR

    Lower… Specifically the axis that is missint steps.

    Riley

    in reply to: Extra Steps? #1470
    Riley
    Keymaster

    Did it work? Was it the thermal shutdown?

    Riley
    Keymaster

    Magic,

    Hey there. Again sorry to hear your issues. Alden and I have been thinking for some time now about selling a 328p uC with grbl pre-loaded. I can expedite this if you are interested. Cost will be around $6.00 (plus shipping) for a pre-loaded Atmega328p with grbl. Something akin to sparkfun’s Arduino 328p pre-loaded bootloader.

    http://www.sparkfun.com/products/10524

    If you want to go this route let me know and I will create a new product in the store. Also, if you want to send me your board I will program it for you for the cost of shipping.

    We truly do not like to hear that our customers are having issues using grblShield (even if its not really the shield that is the issue :).

    Let us know what you would like to do. GrblShield is truly meant to be able to be plugged in and just “work” so lets get that going.

    Riley

    in reply to: Extra Steps? #1464
    Riley
    Keymaster

    Chris,

    Do me a favor. I need you to issue a $$ command and capture the response to a txt file. Paste that txt file into here. We need to verify that your settings. You can set something and screw up your day 🙂 I know I have before.

    Riley

    in reply to: Extra Steps? #1465
    Riley
    Keymaster

    Chris,

    Do me a favor. I need you to issue a $$ command and capture the response to a txt file. Paste that txt file into here. We need to verify that your settings. You can set something and screw up your day 🙂 I know I have before.

    Riley

    in reply to: Best Workflow #1653
    Riley
    Keymaster

    Yah I have been meaning to ask if you upgraded your lead screws? Alden and I have X3 mills.. (his is a bit higher end than mine.. DRO and digital rpm stuff). We are in the market to convert our mills too. However so much to do so little time!

    in reply to: Best Workflow #1650
    Riley
    Keymaster

    The python script that I have been working on is available here: https://github.com/ril3y/ConsoleLoader

    install git (google git download)

    git clone https://github.com/ril3y/ConsoleLoader
    once its done..

    cd ConsoleLoader
    python Consoleloader.py

    Then follow the instructions on screen.. NOTE YOU NEED PYSERIAL.

    However its not fully tested. I have been without power from Irene for about 4 days now. I am planning on testing some tonight. I do know that Windows will not work right now with it. Some issue with the pySerial module.

    This code will be changing frequently. Your best bet is to do a git pull each day until its in a stable state. Open issues on the github page if found.

    Thanks,
    ril3y

    in reply to: Getting motors to turn. #1804
    Riley
    Keymaster

    haha ! OK that works too. Still think your power supply is on the low side. Read alden’s follow up post here:

    http://www.synthetos.com/forums/topic.php?id=231

    Riley

    in reply to: Getting motors to turn. #1802
    Riley
    Keymaster

    @rymanvw,

    Depending on your motor I would assume that you need a bigger power supply. A good test is just to get a PC power supply and use the 12v (yellow normally) to power the board. This will give MUCH more current then 700mah. Try turning the pot all the way to the left then issue a g0x10000 or something similar and turn the pot up until it moves. Let me know if this works out for ya.

    Riley

    in reply to: heatsink? #1749
    Riley
    Keymaster

    These TI chips are pretty nice. And with all the extra copper that alden added to the PCB… It really makes the board pretty tough.

    Riley

    in reply to: Programmed Arduino Chip. #1569
    Riley
    Keymaster

    kf2qd, My thoughts exactly.

    Riley

    in reply to: Using ReplicatorG to stream G-code to Grblshield #1635
    Riley
    Keymaster

    I looked at it briefly. I have not really tried however. If you do it get to work please let us know. Of perhaps a entry in the wiki?

    Thanks,

    in reply to: Programmed Arduino Chip. #1567
    Riley
    Keymaster

    I agree. We are working out how to do this now.

    ril3y

    in reply to: alternative for stepper motor connectors #1778
    Riley
    Keymaster

    Check your emails… We will send a few out.

    in reply to: grbl support for lathe operations #1619
    Riley
    Keymaster

    I know that alden and I have not. Perhaps other grbl users have? However I doubt it.

    Riley

Viewing 15 posts - 241 through 255 (of 260 total)