ergys_

Forum Replies Created

Viewing 6 posts - 1 through 6 (of 6 total)
  • Author
    Posts
  • July 7, 2014 at 7:38 am in reply to: TinyG Connection Issues #6348
    ergys_
    Member

    yes the machine is build but the motors are free at the moment.

    I dont see any bounds of the preview window, or a window in general :/

    $$

    [+]User has entered text mode. To exit type “{” and hit enter.
    [fb] firmware build 412.01
    [fv] firmware version 0.97
    [hp] hardware platform 1.00
    [hv] hardware version 8.00
    [id] TinyG ID 2U2971-QBJ
    [ja] junction acceleration 100000 mm
    [ct] chordal tolerance 0.000 mm
    [sl] soft limit enable 0
    [st] switch type 0 [0=NO,1=NC]
    [mt] motor idle timeout 5.00 Sec
    [ej] enable json mode 0 [0=text,1=JSON]
    [jv] json verbosity 3 [0=silent,1=footer,2=messages,3=configs,4=linenum,5=verbose]
    [js] json serialize style 1 [0=relaxed,1=strict]
    [tv] text verbosity 1 [0=silent,1=verbose]
    [qv] queue report verbosity 0 [0=off,1=single,2=triple]
    [sv] status report verbosity 1 [0=off,1=filtered,2=verbose]
    [si] status interval 250 ms
    [ec] expand LF to CRLF on TX 0 [0=off,1=on]
    [ee] enable echo 0 [0=off,1=on]
    [ex] enable flow control 1 [0=off,1=XON/XOFF, 2=RTS/CTS]

    [baud] USB baud rate 5 [1=9600,2=19200,3=38400,4=57600,5=115200,6=230400]
    [net] network mode 0 [0=master]
    [gpl] default gcode plane 0 [0=G17,1=G18,2=G19]
    [gun] default gcode units mode 1 [0=G20,1=G21]
    [gco] default gcode coord system 1 [1-6 (G54-G59)]
    [gpa] default gcode path control 2 [0=G61,1=G61.1,2=G64]
    [gdi] default gcode distance mode 0 [0=G90,1=G91]
    [1ma] m1 map to axis 0 [0=X,1=Y,2=Z…]
    [1sa] m1 step angle 1.800 deg
    [1tr] m1 travel per revolution 36.5400 mm
    [1mi] m1 microsteps 8 [1,2,4,8]
    [1po] m1 polarity 0 [0=normal,1=reverse]
    [1pm] m1 power management 1 [0=remain powered,1=power down when idle]
    [1mp] m1 motor power level 1.000 [0.000=minimum, 1.000=maximum]
    [2ma] m2 map to axis 1 [0=X,1=Y,2=Z…]
    [2sa] m2 step angle 1.800 deg
    [2tr] m2 travel per revolution 36.5400 mm
    [2mi] m2 microsteps 8 [1,2,4,8]
    [2po] m2 polarity 0 [0=normal,1=reverse]
    [2pm] m2 power management 1 [0=remain powered,1=power down when idle]
    [2mp] m2 motor power level 1.000 [0.000=minimum, 1.000=maximum]
    [3ma] m3 map to axis 2 [0=X,1=Y,2=Z…]
    [3sa] m3 step angle 1.800 deg
    [3tr] m3 travel per revolution 1.2500 mm
    [3mi] m3 microsteps 8 [1,2,4,8]
    [3po] m3 polarity 0 [0=normal,1=reverse]
    [3pm] m3 power management 1 [0=remain powered,1=power down when idle]
    [3mp] m3 motor power level 1.000 [0.000=minimum, 1.000=maximum]
    [4ma] m4 map to axis 0 [0=X,1=Y,2=Z…]
    [4sa] m4 step angle 1.800 deg
    [4tr] m4 travel per revolution 36.5400 mm
    [4mi] m4 microsteps 8 [1,2,4,8]
    [4po] m4 polarity 1 [0=normal,1=reverse]
    [4pm] m4 power management 1 [0=remain powered,1=power down when idle]
    [4mp] m4 motor power level 1.000 [0.000=minimum, 1.000=maximum]
    [xam] x axis mode 1 [standard]
    [xvm] x velocity maximum 16000.000 mm/min
    [xfr] x feedrate maximum 16000.000 mm/min
    [xtn] x travel minimum 0.000 mm
    [xtm] x travel maximum 220.000 mm
    [xjm] x jerk maximum 5000 mm/min^3 * 1 million
    [xjh] x jerk homing 10000 mm/min^3 * 1 million
    [xjd] x junction deviation 0.0100 mm (larger is faster)
    [xsn] x switch min 1 [0=off,1=homing,2=limit,3=limit+homing]
    [xsx] x switch max 0 [0=off,1=homing,2=limit,3=limit+homing]
    [xsv] x search velocity 3000.000 mm/min
    [xlv] x latch velocity 100.000 mm/min
    [xlb] x latch backoff 20.000 mm
    [xzb] x zero backoff 3.000 mm
    [yam] y axis mode 1 [standard]
    [yvm] y velocity maximum 16000.000 mm/min
    [yfr] y feedrate maximum 16000.000 mm/min
    [ytn] y travel minimum 0.000 mm
    [ytm] y travel maximum 220.000 mm
    [yjm] y jerk maximum 5000 mm/min^3 * 1 million
    [yjh] y jerk homing 10000 mm/min^3 * 1 million
    [yjd] y junction deviation 0.0100 mm (larger is faster)
    [ysn] y switch min 1 [0=off,1=homing,2=limit,3=limit+homing]
    [ysx] y switch max 0 [0=off,1=homing,2=limit,3=limit+homing]
    [ysv] y search velocity 3000.000 mm/min
    [ylv] y latch velocity 100.000 mm/min
    [ylb] y latch backoff 20.000 mm
    [yzb] y zero backoff 3.000 mm
    [zam] z axis mode 1 [standard]
    [zvm] z velocity maximum 800.000 mm/min
    [zfr] z feedrate maximum 800.000 mm/min
    [ztn] z travel minimum 0.000 mm
    [ztm] z travel maximum 100.000 mm
    [zjm] z jerk maximum 50 mm/min^3 * 1 million
    [zjh] z jerk homing 1000 mm/min^3 * 1 million
    [zjd] z junction deviation 0.0100 mm (larger is faster)
    [zsn] z switch min 2 [0=off,1=homing,2=limit,3=limit+homing]
    [zsx] z switch max 1 [0=off,1=homing,2=limit,3=limit+homing]
    [zsv] z search velocity 3000.000 mm/min
    [zlv] z latch velocity 100.000 mm/min
    [zlb] z latch backoff 20.000 mm
    [zzb] z zero backoff 3.000 mm
    [aam] a axis mode 1 [standard]
    [avm] a velocity maximum 16000.000 deg/min
    [afr] a feedrate maximum 16000.000 deg/min
    [atn] a travel minimum 0.000 deg
    [atm] a travel maximum 220.000 deg
    [ajm] a jerk maximum 5000 deg/min^3 * 1 million
    [ajh] a jerk homing 5760 deg/min^3 * 1 million
    [ajd] a junction deviation 0.0100 deg (larger is faster)
    [ara] a radius value 0.0000 deg
    [asn] a switch min 1 [0=off,1=homing,2=limit,3=limit+homing]
    [asx] a switch max 0 [0=off,1=homing,2=limit,3=limit+homing]
    [asv] a search velocity 3000.000 deg/min
    [alv] a latch velocity 100.000 deg/min
    [alb] a latch backoff 20.000 deg
    [azb] a zero backoff 3.000 deg
    [bam] b axis mode 0 [disabled]
    [bvm] b velocity maximum 3600.000 deg/min
    [bfr] b feedrate maximum 3600.000 deg/min
    [btn] b travel minimum -1.000 deg
    [btm] b travel maximum -1.000 deg
    [bjm] b jerk maximum 20 deg/min^3 * 1 million
    [bjd] b junction deviation 0.0500 deg (larger is faster)
    [bra] b radius value 1.0000 deg
    [cam] c axis mode 0 [disabled]
    [cvm] c velocity maximum 3600.000 deg/min
    [cfr] c feedrate maximum 3600.000 deg/min
    [ctn] c travel minimum -1.000 deg
    [ctm] c travel maximum -1.000 deg
    [cjm] c jerk maximum 20 deg/min^3 * 1 million
    [ctn] c travel minimum -1.000 deg
    [cjd] c junction deviation 0.0500 deg (larger is faster)
    [cra] c radius value 1.0000 deg
    [p1frq] pwm frequency 100.000 Hz
    [p1csl] pwm cw speed lo 1000.000 RPM
    [p1csh] pwm cw speed hi 2000.000 RPM
    [1cpl] pwm cw phase lo 0.125 [0..1]
    [p1cph] pwm cw phase hi 0.200 [0..1]
    [p1wsl] pwm ccw speed lo 1000.000 RPM
    [p1wsh] pwm ccw speed hi 2000.000 RPM
    [p1wpl] pwm ccw phase lo 0.125 [0..1]
    [p1wph] pwm ccw phase hi 0.200 [0..1]
    [p1pof] pwm phase off 0.100 [0..1]
    [g54x] g54 x offset 0.000 mm
    [g54y] g54 y offset 0.000 mm
    [g54z] g54 z offset 0.000 mm
    [g54a] g54 a offset 0.000 deg
    [g54b] g54 b offset 0.000 deg
    [g54c] g54 c offset 0.000 deg
    [g55x] g55 x offset 75.000 mm
    [g55y] g55 y offset 75.000 mm
    [g55z] g55 z offset 0.000 mm
    [g55a] g55 a offset 0.000 deg
    [g55b] g55 b offset 0.000 deg
    [g55c] g55 c offset 0.000 deg
    [g56x] g56 x offset 0.000 mm
    [g56y] g56 y offset 0.000 mm
    [g56z] g56 z offset 0.000 mm
    [g56a] g56 a offset 0.000 deg
    [g56b] g56 b offset 0.000 deg
    [g56c] g56 c offset 0.000 deg
    [g57x] g57 x offset 0.000 mm
    [g57y] g57 y offset 0.000 mm
    [g57z] g57 z offset 0.000 mm
    [g57a] g57 a offset 0.000 deg
    [g57b] g57 b offset 0.000 deg
    [g57c] g57 c offset 0.000 deg
    [g58x] g58 x offset 0.000 mm
    [g58y] g58 y offset 0.000 mm
    [g58z] g58 z offset 0.000 mm
    [g58a] g58 a offset 0.000 deg
    [g58b] g58 b offset 0.000 deg
    [g58c] g58 c offset 0.000 deg
    [g59x] g59 x offset 0.000 mm
    [g59y] g59 y offset 0.000 mm
    [g59z] g59 z offset 0.000 mm
    [g59a] g59 a offset 0.000 deg
    [g59b] g59 b offset 0.000 deg
    [g59c] g59 c offset 0.000 deg
    [g92x] g92 x offset 0.000 mm
    [g92y] g92 y offset 0.000 mm
    [g92z] g92 z offset 0.000 mm
    [g92a] g92 a offset 0.000 deg
    [g92b] g92 b offset 0.000 deg
    [g92c] g92 c offset 0.000 deg
    [g28x] g28 x position 0.000 mm
    [g28y] g28 y position 0.000 mm
    [g28z] g28 z position 0.000 mm
    [g28a] g28 a position 0.000 deg
    [g28b] g28 b position 0.000 deg
    [g28c] g28 c position 0.000 deg
    [g30x] g30 x position 0.000 mm
    [g30y] g30 y position 0.000 mm
    [g30z] g30 z position 0.000 mm
    [g30a] g30 a position 0.000 deg
    [g30b] g30 b position 0.000 deg
    [g30c] g30 c position 0.000 deg
    tinyg [mm] ok>

    July 7, 2014 at 6:02 am in reply to: TinyG Connection Issues #6342
    ergys_
    Member

    I now downloaded the new tgFX build 3505 and it read all the tinyG settings, it also matches the FW build of the tinyG but the FW version of tgFX is .95 and tinyG is .97

    all the motor and axis settings uploaded and are saved, however I can’t seem to jog any of the motors.

    July 7, 2014 at 4:25 am in reply to: TinyG Connection Issues #6341
    ergys_
    Member

    went back to check the settings of the board and CoolTerm says:

    FW build = 412.01
    FW version = .97

    July 6, 2014 at 8:52 pm in reply to: TinyG Connection Issues #6340
    ergys_
    Member

    Sorry for getting back late each time but the internet connection has not been all that reliable here.

    I’m running it on tgFx build 3259.

    Not really sure how to determine the FW from the $ menu, as I don’t think I see it anywhere. It does give me a tinyG ID if that is helpful in anyway?

    another thing is as I updated all the given parameters for the motors and the others through coolterm, the minute I turned off the power supplier / board, all the data was restored back to it’s previous settings!

    I would really like to run the files through tgFX but I just can’t seem to connect to any of the ports no matter what I do.

    July 6, 2014 at 9:56 am in reply to: TinyG Connection Issues #6338
    ergys_
    Member

    Thanks for the quick response,

    The tinyG hardware is V8 and I’m running it on Windows 7.

    I’ve never had the chance to figure out the build FW in the tinyG because I’ve never been able to connect to it, at least properly.

    However I may have had a small breakthrough and got connected to tinyG through CoolTerm but am not able to receive any kind of information when entering “$+carriage” but I do get all the settings of the board when entering “$”. And i’ve been using port COM5 for all softwares.

    I would be fine with just running the machine through coolterm but I’m not sure how to edit the setting of the motors and such, so when running a gcode through it, it doesn’t want to fall off the rails like it almost did 🙂

    Once I connect to the board through coolterm, I closed it to see if I can run it through tgFX but once again, no luck connecting to it.

    the tgFX firmware build says it is 0.0 and when I try to check online for firmware, and it won’t upload a new FW when I try and do so. I downloaded tgFX through the link below,

    https://github.com/synthetos/tgFX/wiki/Installing-tgFX

    Is there any other software you recommend using or will I be able to update the parameters through coolterm and just use it?

    thank you for your time and quick response!

    July 6, 2014 at 4:50 am in reply to: Need TinyG Help? Try this first! #6334
    ergys_
    Member

    Now most of this may be a little over my head as my lack of involvement or experience comes in to play toward dealing with these issues but I will try my best to explain the issues that I am currently having with the TinyG.

    First, from day one, I have yet been able to establish any kind of connection that’s somewhat reliable. I installed all the drivers required for the board (CDM drivers). Then I installed CoolTerm to test the connection with the board, and as I do so with all the guided directions,

    115,200 baud
    8 data bits
    no parity
    1 stop bit
    XON flow control (assuming you are using XON. See note in Verify Flow Control for RTS/CTS usage)

    Options/Terminal – Line Mode
    Options/Enter Key Emulation – CR

    I can’t get the board to respond with

    {“r”:{“fb”:371.030,”fv”:0.950,”hv”:7.000,”id”:”9H3583-RMP”,”msg”:”Loading configs from EEPROM”,”f”:[1,15,0,8891]}}
    {“r”:{“fb”:371.030,”fv”:0.950,”hv”:7.000,”id”:”9H3583-RMP”,”msg”:”SYSTEM READY”,”f”:[1,0,0,8820]}}
    tinyg [mm] ok>

    I don’t get any error messages or such, it’s as if the computer does not acknowledge the board.

    Then as I go into tgFX to connect the board it wont do so in any of the ports, and it is constantly asking me to upgrade firmware and I have done so for the 10th time at this point. Still no progress.

    I have tried running the cnc machine through JCNC or Universal G-Code, the board connects to both software and does respond to jogging commands but does not run any cutting files correctly.

    Any help would be greatly appreciated at this point. I’m in a middle of a workshop and have yet to get anything done.

    Thanks for your time in advance,

  • Author
    Posts
Viewing 6 posts - 1 through 6 (of 6 total)