Artmaster

Forum Replies Created

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • July 20, 2015 at 5:31 am in reply to: TinyG and ChiliPeppr under Windows 10 Insider Preview #8069
    Artmaster
    Member

    Win10 isn’t problem. It’s clean. Problem is IE11, but I hope could be solved. Thank you.

    • This reply was modified 9 years, 7 months ago by Artmaster.
    July 15, 2015 at 10:03 am in reply to: TinyG and ChiliPeppr under Windows 10 Insider Preview #8007
    Artmaster
    Member

    Thank you very much for your help. You’re righ – the problem was IE11. Under Win 8.1 and IE11 TinyG for CP not working too.
    Under Win 10 IE11 and Spartan – not working. but Win10 and Chrome – its working well.
    Problem could be of serial-port-json-server – I don’t know. More over, I think we can force and tune IE to support this service, but it isn’t my job. I think it’s problem developers of CP, TinyG and serial-port-json-server team. And diode and 2.5 A for motor limit, etc.
    Ok. Now I know more about this software. Let’s go on

    • This reply was modified 9 years, 7 months ago by Artmaster.
    July 14, 2015 at 2:40 am in reply to: TinyG and ChiliPeppr under Windows 10 Insider Preview #7997
    Artmaster
    Member

    I won’t install Chrome yet. I try to use new solution from MS as long as I can. I don’t understand your question about Win 10 traffic, sorry.

    July 13, 2015 at 3:16 pm in reply to: TinyG and ChiliPeppr under Windows 10 Insider Preview #7993
    Artmaster
    Member

    I being used IE11. TinyG was load drivers and good working for CoolTerm_Win under Win10

    July 9, 2015 at 9:29 am in reply to: PWM LED always lighted #7958
    Artmaster
    Member

    Bingo! solve it. already 🙂 I connected to TinyG stepper motor from CDROM as Motor 4 and decreased trimpot to 9 oclock. Stepper moved, LED is off. I’m almost happy.

    done

    • This reply was modified 9 years, 7 months ago by Artmaster.
    July 9, 2015 at 9:01 am in reply to: PWM LED always lighted #7956
    Artmaster
    Member

    Pardon me. I use the command $p1pof = 0.0, but it’s Lighting anyway. Just interesting… how it’s work?!

    Lighting anyway

    July 3, 2015 at 9:50 am in reply to: PWM LED always lighted #7935
    Artmaster
    Member

    Of course I learn this page and will do that many times.. Thank you for your help.
    By the way. Many times I met attention about polarity of PS for TinyG. is it difficult to install diode and close that sourse of disaster?

    July 3, 2015 at 8:27 am in reply to: PWM LED always lighted #7933
    Artmaster
    Member

    “$p1pof = 0.1 means that in the off state, the PWM phase (pulse width) is 10%.”
    – I understand now. Thank you.
    The LED is illustrate indefinite state of pulse width on the moment. I’m just wonder – usualy that LED isn’t lighting on the video from other people -that’s why I worried.
    Will be nice to get table of state for LED’s, pin’s volumes for any operations…

    July 3, 2015 at 6:54 am in reply to: PWM LED always lighted #7929
    Artmaster
    Member

    Thank you, but there are CJM Controller installed and have reason to set up, or change value of $p1pof.
    Let me know please, same condition, like mine – is it normal mode of LED, CoolTermWin return?

  • Author
    Posts
Viewing 9 posts - 1 through 9 (of 9 total)