rickkaye

Forum Replies Created

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • September 10, 2013 at 2:39 pm in reply to: Board won't execute GCode #4506
    rickkaye
    Member

    I restored every parameter in the $$ listing to their values while the problem was present (except $xvm which I set to 3000). Everything worked fine.

    Then I issued commands including gcode commands using JSON. Everything worked fine.

    Then I remembered that you had noticed that $xvm was set to 0. I set it to 0 and tried moving the X motor. Of course nothing happened. I tried moving the Y motor, nothing happened. I was able to read and change parameters but no gcode commands worked. The problem was back. I changed $xvm back to 3000. Gcode still didn’t work.

    I rebooted the tinyG a few times trying several things. It turns out that the only way I could get it to work was to reboot and then set $xvm to a positive value as the first thing I did after a reboot. This is what I effectively did yesterday when you had me do a $defa=1 and I did it immediately after a reboot.

    I still don’t know how $xvm got set to 0 in the first place. But everything is working now and I know how to cure the problem if it recurs.

    Thanks again.

    September 9, 2013 at 4:25 pm in reply to: Board won't execute GCode #4496
    rickkaye
    Member

    Strange! I had powered the board off before and I had done a $defa=1 before but not sequentially. This time I powered it off and then on, then did the $defa=1 as the first command and then captured the output to send to you. Before sending I tried a g0x30 command and it worked.

    I will look into it tonight (Pacific time) to see if I can figure out what’s different.

    In the meantime, for the record, the captured output is below. Thanks for your help.

    Here it is:

    tinyg [mm] ok>
    $defa=1
    {“r”:{“fb”:377.08,”fv”:0.950,”hv”:7,”id”:”9H3583-KCR”,”msg”:”Initializing configs to default settings”,”f”:[1,15,8,5568]}}
    tinyg [mm] ok>
    line:0,posx:0.000,posy:0.000,posz:0.000,posa:0.000,feed:0.000,vel:0.000,unit:1,coor:1,dist:0,frmo:0,momo:4,stat:1
    [fb] firmware build 377.08
    [fv] firmware version 0.95
    [hv] hardware version 7.00
    [id] TinyG ID 9H3583-KCR
    [ja] junction acceleration 100000 mm
    [ct] chordal tolerance 0.001 mm
    [st] switch type 0 [0=NO,1=NC]
    [ej] enable json mode 0 [0=text,1=JSON]
    [jv] json verbosity 4 [0=silent,1=footer,2=messages,3=configs,4=linenum,5=verbose]
    [tv] text verbosity 1 [0=silent,1=verbose]
    [qv] queue report verbosity 0 [0=off,1=filtered,2=verbose]
    [sv] status report verbosity 1 [0=off,1=filtered,2=verbose]
    [si] status interval 250 ms
    [ic] ignore CR or LF on RX 0 [0=off,1=CR,2=LF]
    [ec] expand LF to CRLF on TX 0 [0=off,1=on]
    [ee] enable echo 0 [0=off,1=on]
    [ex] enable xon xoff 1 [0=off,1=on]
    [baud] USB baud rate 5 [1=9600,2=19200,3=38400,4=57600,5=115200,6=230400]
    [gpl] default gcode plane 0 [0=G17,1=G18,2=G19]
    [gun] default gcode units mode 1 [0=G20,1=G21]
    [gco] default gcode coord system 1 [1-6 (G54-G59)]
    [gpa] default gcode path control 2 [0=G61,1=G61.1,2=G64]
    [gdi] default gcode distance mode 0 [0=G90,1=G91]
    [1ma] m1 map to axis 0 [0=X,1=Y,2=Z…]
    [1sa] m1 step angle 1.800 deg
    [1tr] m1 travel per revolution 1.250 mm
    [1mi] m1 microsteps 8 [1,2,4,8]
    [1po] m1 polarity 0 [0=normal,1=reverse]
    [1pm] m1 power management 1 [0=off,1=on]
    [2ma] m2 map to axis 1 [0=X,1=Y,2=Z…]
    [2sa] m2 step angle 1.800 deg
    [2tr] m2 travel per revolution 1.250 mm
    [2mi] m2 microsteps 8 [1,2,4,8]
    [2po] m2 polarity 0 [0=normal,1=reverse]
    [2pm] m2 power management 1 [0=off,1=on]
    [3ma] m3 map to axis 2 [0=X,1=Y,2=Z…]
    [3sa] m3 step angle 1.800 deg
    [3tr] m3 travel per revolution 1.250 mm
    [3mi] m3 microsteps 8 [1,2,4,8]
    [3po] m3 polarity 0 [0=normal,1=reverse]
    [3pm] m3 power management 1 [0=off,1=on]
    [4ma] m4 map to axis 3 [0=X,1=Y,2=Z…]
    [4sa] m4 step angle 1.800 deg
    [4tr] m4 travel per revolution 360.000 mm
    [4mi] m4 microsteps 8 [1,2,4,8]
    [4po] m4 polarity 0 [0=normal,1=reverse]
    [4pm] m4 power management 1 [0=off,1=on]
    [xam] x axis mode 1 [standard]
    [xvm] x velocity maximum 600.000 mm/min
    [xfr] x feedrate maximum 600.000 mm/min
    [xtm] x travel maximum 150.000 mm
    [xjm] x jerk maximum 20000000 mm/min^3
    [xjh] x jerk homing 20000000 mm/min^3
    [xjd] x junction deviation 0.0500 mm (larger is faster)
    [xsn] x switch min 1 [0=off,1=homing,2=limit,3=limit+homing]
    [xsx] x switch max 0 [0=off,1=homing,2=limit,3=limit+homing]
    [xsv] x search velocity 500.000 mm/min
    [xlv] x latch velocity 100.000 mm/min
    [xlb] x latch backoff 2.000 mm
    [xzb] x zero backoff 1.000 mm
    [yam] y axis mode 1 [standard]
    [yvm] y velocity maximum 600.000 mm/min
    [yfr] y feedrate maximum 600.000 mm/min
    [ytm] y travel maximum 150.000 mm
    [yjm] y jerk maximum 20000000 mm/min^3
    [yjh] y jerk homing 20000000 mm/min^3
    [yjd] y junction deviation 0.0500 mm (larger is faster)
    [ysn] y switch min 1 [0=off,1=homing,2=limit,3=limit+homing]
    [ysx] y switch max 0 [0=off,1=homing,2=limit,3=limit+homing]
    [ysv] y search velocity 500.000 mm/min
    [ylv] y latch velocity 100.000 mm/min
    [ylb] y latch backoff 2.000 mm
    [yzb] y zero backoff 1.000 mm
    [zam] z axis mode 1 [standard]
    [zvm] z velocity maximum 600.000 mm/min
    [zfr] z feedrate maximum 600.000 mm/min
    [ztm] z travel maximum 75.000 mm
    [zjm] z jerk maximum 20000000 mm/min^3
    [zjh] z jerk homing 20000000 mm/min^3
    [zjd] z junction deviation 0.0500 mm (larger is faster)
    [zsn] z switch min 0 [0=off,1=homing,2=limit,3=limit+homing]
    [zsx] z switch max 1 [0=off,1=homing,2=limit,3=limit+homing]
    [zsv] z search velocity 400.000 mm/min
    [zlv] z latch velocity 100.000 mm/min
    [zlb] z latch backoff 2.000 mm
    [zzb] z zero backoff 1.000 mm
    [aam] a axis mode 3 [radius]
    [avm] a velocity maximum 172800.000 deg/min
    [afr] a feedrate maximum 172800.000 deg/min
    [atm] a travel maximum -1.000 deg
    [ajm] a jerk maximum 5760000000 deg/min^3
    [ajh] a jerk homing 5760000000 mm/min^3
    [ajd] a junction deviation 0.0500 deg (larger is faster)
    [ara] a radius value 0.1989 deg
    [asn] a switch min 1 [0=off,1=homing,2=limit,3=limit+homing]
    [asx] a switch max 0 [0=off,1=homing,2=limit,3=limit+homing]
    [asv] a search velocity 600.000 deg/min
    [alv] a latch velocity 100.000 deg/min
    [alb] a latch backoff 5.000 deg
    [azb] a zero backoff 2.000 deg
    [bam] b axis mode 0 [disabled]
    [bvm] b velocity maximum 3600.000 deg/min
    [bfr] b feedrate maximum 3600.000 deg/min
    [btm] b travel maximum -1.000 deg
    [bjm] b jerk maximum 20000000 deg/min^3
    [bjd] b junction deviation 0.0500 deg (larger is faster)
    [bra] b radius value 1.0000 deg
    [cam] c axis mode 0 [disabled]
    [cvm] c velocity maximum 3600.000 deg/min
    [cfr] c feedrate maximum 3600.000 deg/min
    [ctm] c travel maximum -1.000 deg
    [cjm] c jerk maximum 20000000 deg/min^3
    [cjd] c junction deviation 0.0500 deg (larger is faster)
    [cra] c radius value 1.0000 deg
    [p1frq] pwm frequency 100.000 Hz
    [p1csl] pwm cw speed lo 1000.000 RPM
    [p1csh] pwm cw speed hi 2000.000 RPM
    [p1cpl] pwm cw phase lo 0.125 [0..1]
    [p1cph] pwm cw phase hi 0.200 [0..1]
    [p1wsl] pwm ccw speed lo 1000.000 RPM
    [p1wsh] pwm ccw speed hi 2000.000 RPM
    [p1wpl] pwm ccw phase lo 0.125 [0..1]
    [p1wph] pwm ccw phase hi 0.200 [0..1]
    [p1pof] pwm phase off 0.100 [0..1]
    [g54x] g54 x offset 0.000 mm
    [g54y] g54 y offset 0.000 mm
    [g54z] g54 z offset 0.000 mm
    [g54a] g54 a offset 0.000 deg
    [g54b] g54 b offset 0.000 deg
    [g54c] g54 c offset 0.000 deg
    [g55x] g55 x offset 75.000 mm
    [g55y] g55 y offset 75.000 mm
    [g55z] g55 z offset 0.000 mm
    [g55a] g55 a offset 0.000 deg
    [g55b] g55 b offset 0.000 deg
    [g55c] g55 c offset 0.000 deg
    [g56x] g56 x offset 0.000 mm
    [g56y] g56 y offset 0.000 mm
    [g56z] g56 z offset 0.000 mm
    [g56a] g56 a offset 0.000 deg
    [g56b] g56 b offset 0.000 deg
    [g56c] g56 c offset 0.000 deg
    [g57x] g57 x offset 0.000 mm
    [g57y] g57 y offset 0.000 mm
    [g57z] g57 z offset 0.000 mm
    [g57a] g57 a offset 0.000 deg
    [g57b] g57 b offset 0.000 deg
    [g57c] g57 c offset 0.000 deg
    [g58x] g58 x offset 0.000 mm
    [g58y] g58 y offset 0.000 mm
    [g58z] g58 z offset 0.000 mm
    [g58a] g58 a offset 0.000 deg
    [g58b] g58 b offset 0.000 deg
    [g58c] g58 c offset 0.000 deg
    [g59x] g59 x offset 0.000 mm
    [g59y] g59 y offset 0.000 mm
    [g59z] g59 z offset 0.000 mm
    [g59a] g59 a offset 0.000 deg
    [g59b] g59 b offset 0.000 deg
    [g59c] g59 c offset 0.000 deg
    [g92x] g92 x offset 0.000 mm
    [g92y] g92 y offset 0.000 mm
    [g92z] g92 z offset 0.000 mm
    [g92a] g92 a offset 0.000 deg
    [g92b] g92 b offset 0.000 deg
    [g92c] g92 c offset 0.000 deg
    [g28x] g28 x location 0.000 mm
    [g28y] g28 y location 0.000 mm
    [g28z] g28 z location 0.000 mm
    [g28a] g28 a location 0.000 deg
    [g28b] g28 b location 0.000 deg
    [g28c] g28 c location 0.000 deg
    [g30x] g30 x location 0.000 mm
    [g30y] g30 y location 0.000 mm
    [g30z] g30 z location 0.000 mm
    [g30a] g30 a location 0.000 deg
    [g30b] g30 b location 0.000 deg
    [g30c] g30 c location 0.000 deg
    tinyg [mm] ok>

    September 9, 2013 at 4:07 pm in reply to: Board won't execute GCode #4494
    rickkaye
    Member

    I tried everything you suggested but nothing helped. I did notice that I am getting some spontaneous output from the tinyG. For example, at the first prompt below, I typed g0x30 which is echoed on the next line, at the second prompt, I did not type anything but the next line (momo:0) appeared.

    tinyg [mm] ok>
    g0x30
    tinyg [mm] ok>
    momo:0

    The same thing happened (see below) when I tried the g1 f100 x5 command that you suggested. But this time it spontaneously printed momo:1.

    tinyg [mm] ok>
    g1 f100 x5
    tinyg [mm] ok>
    momo:1

    I don’t know if any of this is related but I don’t remember seeing spontaneously lines from the tinyG before.

    Thanks again.

    September 9, 2013 at 2:33 pm in reply to: Board won't execute GCode #4492
    rickkaye
    Member

    As you can see below, still nothing moves. I had already changed $xvm but I retyped it as you instructed. Neither the X or Y motor responded. I reset the defaults. The motor didn’t respond when I did a “g0x30”. The command didn’t show up on the terminal. I remembered that I needed to set $ee=1 which I did and then did a “g0x30” again so you could see what I typed.

    Transcript below. Thanks.

    tinyg [mm] ok>
    ?
    Line number: 0
    X position: 0.000 mm
    Y position: 0.000 mm
    Z position: 0.000 mm
    A position: 0.000 deg
    Feed rate: 0.000 mm/min
    Velocity: 0.000 mm/min
    Units: G21 – millimeter mode
    Coordinate system: G54 – coordinate system 1
    Distance mode: G90 – absolute distance mode
    Feed rate mode: G94 – units-per-minute mode (i.e. feedrate mode)
    Motion mode: G0 – linear traverse (seek)
    Machine state: Run
    tinyg [mm] ok>
    $xvm=3000
    [xvm] velocity maximum 3000.000 mm/min
    tinyg [mm] ok>
    g0x30
    tinyg [mm] ok>
    g0y30
    tinyg [mm] ok>
    ?
    Line number: 0
    X position: 0.000 mm
    Y position: 0.000 mm
    Z position: 0.000 mm
    A position: 0.000 deg
    Feed rate: 0.000 mm/min
    Velocity: 0.000 mm/min
    Units: G21 – millimeter mode
    Coordinate system: G54 – coordinate system 1
    Distance mode: G90 – absolute distance mode
    Feed rate mode: G94 – units-per-minute mode (i.e. feedrate mode)
    Motion mode: G0 – linear traverse (seek)
    Machine state: Run
    tinyg [mm] ok>
    $defa=1
    {“r”:{“fb”:377.08,”fv”:0.950,”hv”:7,”id”:”9H3583-KCR”,”msg”:”Initializing configs to default settings”,”f”:[1,15,8,5568]}}
    tinyg [mm] ok>
    Line number: 0
    X position: 0.000 mm
    Y position: 0.000 mm
    Z position: 0.000 mm
    A position: 0.000 deg
    Feed rate: 0.000 mm/min
    Velocity: 0.000 mm/min
    Units: G21 – millimeter mode
    Coordinate system: G54 – coordinate system 1
    Distance mode: G90 – absolute distance mode
    Feed rate mode: G94 – units-per-minute mode (i.e. feedrate mode)
    Motion mode: G0 – linear traverse (seek)
    Machine state: Run
    tinyg [mm] ok>
    tinyg [mm] ok>
    tinyg [mm] ok>
    [ee] enable echo 0 [0=off,1=on]
    tinyg [mm] ok>
    [ee] enable echo 1 [0=off,1=on]
    tinyg [mm] ok>
    g0x30
    tinyg [mm] ok>
    $xvm
    [xvm] velocity maximum 600.000 mm/min
    tinyg [mm] ok>
    line:0,posx:0.000,posy:0.000,posz:0.000,posa:0.000,feed:0.000,vel:0.000,unit:1,coor:1,dist:0,frmo:0,momo:0,stat:5

    September 9, 2013 at 2:08 pm in reply to: Board won't execute GCode #4490
    rickkaye
    Member

    I have no idea how that happened but changing it doesn’t fix the problem. I guess I hadn’t mentioned it above but the Y and Z motors don’t move either.

    tinyg [mm] ok>
    ?
    Line number: 0
    X position: 0.000 mm
    Y position: 0.000 mm
    Z position: 0.000 mm
    A position: 0.000 deg
    Feed rate: 0.000 mm/min
    Velocity: 0.000 mm/min
    Units: G21 – millimeter mode
    Coordinate system: G54 – coordinate system 1
    Distance mode: G90 – absolute distance mode
    Feed rate mode: G94 – units-per-minute mode (i.e. feedrate mode)
    Motion mode: G0 – linear traverse (seek)
    Machine state: Run
    tinyg [mm] ok>
    g0x30
    tinyg [mm] ok>
    momo:0,stat:5
    $xvm
    [xvm] velocity maximum 0.000 mm/min
    tinyg [mm] ok>
    $yvm
    [yvm] velocity maximum 3000.000 mm/min
    tinyg [mm] ok>
    g0y30
    tinyg [mm] ok>
    $xvm=3000
    [xvm] velocity maximum 3000.000 mm/min
    tinyg [mm] ok>
    $xvm
    [xvm] velocity maximum 3000.000 mm/min
    tinyg [mm] ok>
    g0x30
    tinyg [mm] ok>
    ?
    Line number: 0
    X position: 0.000 mm
    Y position: 0.000 mm
    Z position: 0.000 mm
    A position: 0.000 deg
    Feed rate: 0.000 mm/min
    Velocity: 0.000 mm/min
    Units: G21 – millimeter mode
    Coordinate system: G54 – coordinate system 1
    Distance mode: G90 – absolute distance mode
    Feed rate mode: G94 – units-per-minute mode (i.e. feedrate mode)
    Motion mode: G0 – linear traverse (seek)
    Machine state: Run

    September 9, 2013 at 12:02 pm in reply to: Board won't execute GCode #4488
    rickkaye
    Member

    I can’t remember what setting I changed but I do remember that I immediately changed it back to its previous value since I was only testing. Below is the $$ dump. Thanks for your help.

    tinyg [mm] ok>
    $$
    [fb] firmware build 377.08
    [fv] firmware version 0.95
    [hv] hardware version 7.00
    [id] TinyG ID 9H3583-KCR
    [ja] junction acceleration 100000 mm
    [ct] chordal tolerance 0.001 mm
    [st] switch type 1 [0=NO,1=NC]
    [ej] enable json mode 0 [0=text,1=JSON]
    [jv] json verbosity 4 [0=silent,1=footer,2=messages,3=configs,4=linenum,5=verbose]
    [tv] text verbosity 1 [0=silent,1=verbose]
    [qv] queue report verbosity 0 [0=off,1=filtered,2=verbose]
    [sv] status report verbosity 1 [0=off,1=filtered,2=verbose]
    [si] status interval 250 ms
    [ic] ignore CR or LF on RX 0 [0=off,1=CR,2=LF]
    [ec] expand LF to CRLF on TX 0 [0=off,1=on]
    [ee] enable echo 1 [0=off,1=on]
    [ex] enable xon xoff 1 [0=off,1=on]
    [baud] USB baud rate 5 [1=9600,2=19200,3=38400,4=57600,5=115200,6=230400]
    [gpl] default gcode plane 0 [0=G17,1=G18,2=G19]
    [gun] default gcode units mode 1 [0=G20,1=G21]
    [gco] default gcode coord system 1 [1-6 (G54-G59)]
    [gpa] default gcode path control 2 [0=G61,1=G61.1,2=G64]
    [gdi] default gcode distance mode 0 [0=G90,1=G91]
    [1ma] m1 map to axis 0 [0=X,1=Y,2=Z…]
    [1sa] m1 step angle 1.800 deg
    [1tr] m1 travel per revolution 35.800 mm
    [1mi] m1 microsteps 8 [1,2,4,8]
    [1po] m1 polarity 1 [0=normal,1=reverse]
    [1pm] m1 power management 1 [0=off,1=on]
    [2ma] m2 map to axis 1 [0=X,1=Y,2=Z…]
    [2sa] m2 step angle 1.800 deg
    [2tr] m2 travel per revolution 36.750 mm
    [2mi] m2 microsteps 8 [1,2,4,8]
    [2po] m2 polarity 1 [0=normal,1=reverse]
    [2pm] m2 power management 1 [0=off,1=on]
    [3ma] m3 map to axis 2 [0=X,1=Y,2=Z…]
    [3sa] m3 step angle 1.800 deg
    [3tr] m3 travel per revolution 1.410 mm
    [3mi] m3 microsteps 8 [1,2,4,8]
    [3po] m3 polarity 0 [0=normal,1=reverse]
    [3pm] m3 power management 1 [0=off,1=on]
    [4ma] m4 map to axis 3 [0=X,1=Y,2=Z…]
    [4sa] m4 step angle 1.800 deg
    [4tr] m4 travel per revolution 360.000 mm
    [4mi] m4 microsteps 8 [1,2,4,8]
    [4po] m4 polarity 0 [0=normal,1=reverse]
    [4pm] m4 power management 1 [0=off,1=on]
    [xam] x axis mode 1 [standard]
    [xvm] x velocity maximum 0.000 mm/min
    [xfr] x feedrate maximum 3000.000 mm/min
    [xtm] x travel maximum 200.000 mm
    [xjm] x jerk maximum 20000000 mm/min^3
    [xjh] x jerk homing 20000000 mm/min^3
    [xjd] x junction deviation 0.0500 mm (larger is faster)
    [xsn] x switch min 3 [0=off,1=homing,2=limit,3=limit+homing]
    [xsx] x switch max 0 [0=off,1=homing,2=limit,3=limit+homing]
    [xsv] x search velocity 300.000 mm/min
    [xlv] x latch velocity 250.000 mm/min
    [xlb] x latch backoff 8.000 mm
    [xzb] x zero backoff 1.000 mm
    [yam] y axis mode 1 [standard]
    [yvm] y velocity maximum 3000.000 mm/min
    [yfr] y feedrate maximum 3000.000 mm/min
    [ytm] y travel maximum 200.000 mm
    [yjm] y jerk maximum 20000000 mm/min^3
    [yjh] y jerk homing 20000000 mm/min^3
    [yjd] y junction deviation 0.0500 mm (larger is faster)
    [ysn] y switch min 3 [0=off,1=homing,2=limit,3=limit+homing]
    [ysx] y switch max 0 [0=off,1=homing,2=limit,3=limit+homing]
    [ysv] y search velocity 300.000 mm/min
    [ylv] y latch velocity 250.000 mm/min
    [ylb] y latch backoff 8.000 mm
    [yzb] y zero backoff 3.000 mm
    [zam] z axis mode 1 [standard]
    [zvm] z velocity maximum 1500.000 mm/min
    [zfr] z feedrate maximum 600.000 mm/min
    [ztm] z travel maximum 200.000 mm
    [zjm] z jerk maximum 20000000 mm/min^3
    [zjh] z jerk homing 20000000 mm/min^3
    [zjd] z junction deviation 0.0500 mm (larger is faster)
    [zsn] z switch min 3 [0=off,1=homing,2=limit,3=limit+homing]
    [zsx] z switch max 0 [0=off,1=homing,2=limit,3=limit+homing]
    [zsv] z search velocity 300.000 mm/min
    [zlv] z latch velocity 100.000 mm/min
    [zlb] z latch backoff 5.000 mm
    [zzb] z zero backoff 3.000 mm
    [aam] a axis mode 3 [radius]
    [avm] a velocity maximum 172800.000 deg/min
    [afr] a feedrate maximum 172800.000 deg/min
    [atm] a travel maximum -1.000 deg
    [ajm] a jerk maximum 5760000000 deg/min^3
    [ajh] a jerk homing 5760000000 mm/min^3
    [ajd] a junction deviation 0.0500 deg (larger is faster)
    [ara] a radius value 0.1989 deg
    [asn] a switch min 1 [0=off,1=homing,2=limit,3=limit+homing]
    [asx] a switch max 0 [0=off,1=homing,2=limit,3=limit+homing]
    [asv] a search velocity 600.000 deg/min
    [alv] a latch velocity 100.000 deg/min
    [alb] a latch backoff 5.000 deg
    [azb] a zero backoff 2.000 deg
    [bam] b axis mode 0 [disabled]
    [bvm] b velocity maximum 3600.000 deg/min
    [bfr] b feedrate maximum 3600.000 deg/min
    [btm] b travel maximum -1.000 deg
    [bjm] b jerk maximum 20000000 deg/min^3
    [bjd] b junction deviation 0.0500 deg (larger is faster)
    [bra] b radius value 1.0000 deg
    [cam] c axis mode 0 [disabled]
    [cvm] c velocity maximum 3600.000 deg/min
    [cfr] c feedrate maximum 3600.000 deg/min
    [ctm] c travel maximum -1.000 deg
    [cjm] c jerk maximum 20000000 deg/min^3
    [cjd] c junction deviation 0.0500 deg (larger is faster)
    [cra] c radius value 1.0000 deg
    [p1frq] pwm frequency 100.000 Hz
    [p1csl] pwm cw speed lo 1000.000 RPM
    [p1csh] pwm cw speed hi 2000.000 RPM
    [p1cpl] pwm cw phase lo 0.125 [0..1]
    [p1cph] pwm cw phase hi 0.200 [0..1]
    [p1wsl] pwm ccw speed lo 1000.000 RPM
    [p1wsh] pwm ccw speed hi 2000.000 RPM
    [p1wpl] pwm ccw phase lo 0.125 [0..1]
    [p1wph] pwm ccw phase hi 0.200 [0..1]
    [p1pof] pwm phase off 0.100 [0..1]
    [g54x] g54 x offset 0.000 mm
    [g54y] g54 y offset 0.000 mm
    [g54z] g54 z offset 0.000 mm
    [g54a] g54 a offset 0.000 deg
    [g54b] g54 b offset 0.000 deg
    [g54c] g54 c offset 0.000 deg
    [g55x] g55 x offset 75.000 mm
    [g55y] g55 y offset 75.000 mm
    [g55z] g55 z offset 0.000 mm
    [g55a] g55 a offset 0.000 deg
    [g55b] g55 b offset 0.000 deg
    [g55c] g55 c offset 0.000 deg
    [g56x] g56 x offset 0.000 mm
    [g56y] g56 y offset 0.000 mm
    [g56z] g56 z offset 0.000 mm
    [g56a] g56 a offset 0.000 deg
    [g56b] g56 b offset 0.000 deg
    [g56c] g56 c offset 0.000 deg
    [g57x] g57 x offset 0.000 mm
    [g57y] g57 y offset 0.000 mm
    [g57z] g57 z offset 0.000 mm
    [g57a] g57 a offset 0.000 deg
    [g57b] g57 b offset 0.000 deg
    [g57c] g57 c offset 0.000 deg
    [g58x] g58 x offset 0.000 mm
    [g58y] g58 y offset 0.000 mm
    [g58z] g58 z offset 0.000 mm
    [g58a] g58 a offset 0.000 deg
    [g58b] g58 b offset 0.000 deg
    [g58c] g58 c offset 0.000 deg
    [g59x] g59 x offset 0.000 mm
    [g59y] g59 y offset 0.000 mm
    [g59z] g59 z offset 0.000 mm
    [g59a] g59 a offset 0.000 deg
    [g59b] g59 b offset 0.000 deg
    [g59c] g59 c offset 0.000 deg
    [g92x] g92 x offset 0.000 mm
    [g92y] g92 y offset 0.000 mm
    [g92z] g92 z offset 0.000 mm
    [g92a] g92 a offset 0.000 deg
    [g92b] g92 b offset 0.000 deg
    [g92c] g92 c offset 0.000 deg
    [g28x] g28 x location 0.000 mm
    [g28y] g28 y location 0.000 mm
    [g28z] g28 z location 0.000 mm
    [g28a] g28 a location 0.000 deg
    [g28b] g28 b location 0.000 deg
    [g28c] g28 c location 0.000 deg
    [g30x] g30 x location 0.000 mm
    [g30y] g30 y location 0.000 mm
    [g30z] g30 z location 0.000 mm
    [g30a] g30 a location 0.000 deg
    [g30b] g30 b location 0.000 deg
    [g30c] g30 c location 0.000 deg
    tinyg [mm] ok>

    June 22, 2013 at 6:21 pm in reply to: TinyG + Raspberry Pi #4221
    rickkaye
    Member

    Thanks for the update. miniterm works here over USB:

    miniterm.py –cr /dev/ttyUSB0 115200

    June 21, 2013 at 12:12 am in reply to: TinyG stopped responding? #4205
    rickkaye
    Member

    I looked at Tobin’s thread. Just so you know while trying to determine the cause, my TinyG is several weeks old, not new like his. It had no problems before a couple of days ago, Also, I’ve never used tgFX. He mentions turning a pot. I adjusted the motor 1 pot when I first got the board, had no problems, and haven’t touched it since.

    I will let you know if a problem develops again.

    June 20, 2013 at 7:23 pm in reply to: TinyG stopped responding? #4203
    rickkaye
    Member

    That worked. I re-flashed the system and it is now working.

    So, now back to your original response. Do you expect the problem to recur? I do not have an avrprogrammer. Does that mean I should swap for a new board?

    Now that it is running is there anything I can provide to you that would help diagnose what caused the problem?

    Thanks for the help.

    June 20, 2013 at 6:34 pm in reply to: TinyG stopped responding? #4197
    rickkaye
    Member

    Thanks for your help.

    I do not have a power switch. I power off the tinyg by unplugging from the wall. The firmware is 0.95.

    I’m working on finding up-to-date avrdude. I’m on a Mac and when I download the Arduino software as recommended in the instructions, all I get is Arduino.app.

    June 1, 2013 at 10:41 pm in reply to: TinyG + Raspberry Pi #4159
    rickkaye
    Member

    Yes, I had it set to 115,200 8N1. Since I couldn’t get minicom to work, I moved on to controlling the TinyG with a python script as burnsb described above. That worked perfectly. Then I just tried the command line command
    echo g0x100 > /dev/ttyUSB0
    and that worked. So, the minicom failure is still a mystery. Now, I will write a C program to control the TinyG which is my ultimate goal anyway.

    May 30, 2013 at 7:38 pm in reply to: TinyG + Raspberry Pi #4155
    rickkaye
    Member

    I am trying to control my TinyG from a Raspberry Pi. Unlike the OP, I am connecting them through a USB cable (/dev/ttyUSB0). Using minicom on the RP, I can’t get the TinyG to respond. When I press the reset button on the TinyG, minicom sees the TinyG output, so I know the connection is good. The TinyG also responds fine when I connect it to my Mac over USB.

    I was wondering if you had any thoughts on what might be wrong. Thanks.

    Rick

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)