julian

Forum Replies Created

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • November 27, 2012 at 12:32 am in reply to: grbl+shapeoko mod x axis #3621
    julian
    Member

    Well. i tried to update the firmware to 0.8c but.. i keep getting these error.

    avrdude: stk500_recv(): programmer is not responding

    could be a problem from the seeduino?

    November 26, 2012 at 6:07 pm in reply to: grbl+shapeoko mod x axis #3618
    julian
    Member

    The main problem, from what i see its that X Moves, not smoothly enough, but moves. But when i try to print Something.

    EI

    G0 X-3.0 Y-0.0451 …. Worked
    G1 F10.0 Z-0.001 …. Worked
    G1 F60.0 X-2.8845 Y-0.035 … Only Y moves (The light of the X Axis doesn’t light up)
    G3 X-2.8723 Y-0.0943 I0.3244 J0.0363 … Only Y moves
    G3 X-2.8467 Y-0.1492 I0.2072 J0.0631 … Only Y moves
    G3 X-2.805 Y-0.1917 I0.1471 J0.1027 … Only Y moves
    ….

     

    • This reply was modified 12 years, 3 months ago by julian.
    November 26, 2012 at 6:02 pm in reply to: grbl+shapeoko mod x axis #3617
    julian
    Member

    Its not a mechanical issue, cause if i swamp axis, X with Y. X Starts to work, and Y no.

    November 26, 2012 at 10:59 am in reply to: grbl+shapeoko mod x axis #3614
    julian
    Member

    I Did the test.

    G1 z10 F100 Worked

    G1 z0 F200 Worked

    G1 x10 F100 Worked

    G1 x0 F200 Worked

    November 24, 2012 at 12:14 pm in reply to: grbl+shapeoko mod x axis #3610
    julian
    Member

    I couldn’t embed the video, so here’s the link http://www.youtube.com/watch?v=gnrqg9QIKbY

    • This reply was modified 12 years, 3 months ago by julian.
    November 24, 2012 at 11:52 am in reply to: grbl+shapeoko mod x axis #3608
    julian
    Member

    Here its a small video.

    Moves order.

    G0 X1 Y0 Z0… Worked
    G0 X0 Y0 Z0… Worked
    G0 X1Y0 Z0… Worked
    G0 X5 Y0 Z0… Worked
    G0 X-5 Y0 Z0… Worked
    G0 X5 Y0 Z0… Error

    • This reply was modified 12 years, 3 months ago by julian.
    November 24, 2012 at 11:44 am in reply to: grbl+shapeoko mod x axis #3607
    julian
    Member

    My Settings.

    $0 = 43.74
    $1= 43.74
    $2 = 320
    $3 = 30
    $4 = 500
    $5 = 500
    $6 = 0.10
    $7 = 168
    $8 = 50
    $9 =  0.05

    November 23, 2012 at 10:36 am in reply to: grbl+shapeoko mod x axis #3604
    julian
    Member

    Basically the problem its the X axis.

    When i command to move the X axis 1 Step, it moves perfectly.

    When i command to move the X axis 5 Steps, it moves perfectly.

    When i command to move the X axis 10 Steps, makes a noise and doesn’t move at all. These also happends when i want to print something.

     

    October 22, 2012 at 8:42 am in reply to: Y axis doesn’t drive stepper #3571
    julian
    Member

    Hey guys i been having some trouble with the X axis.

    When i start a job it may work the first 20 steps (if i’m lucky).

    The pot only works between 15 – 16 hours. i can’t over torque more than that, if i do it doesn’t move at all. and it doesn’t move as smooth as the other axis.

    I Checked the windings and the motors, i got the shapeoko bundlle.

    – Julian.

  • Author
    Posts
Viewing 9 posts - 1 through 9 (of 9 total)